1:35th Scale unless otherwise stated
- 24303 M3A3 Replacement Turret (AFV Club)
This is a direct replacement of the turret pieces in your AFV CLUB M3A3 kit# AF35053.
In addition to TMD items 20005 and 24301, the replacement turret:
• Saves the time and difficulties of assembling the AFV CLUB kit pieces
• Correctly aligns the “break point” between the turret sides and turret roof
• Does not have the sunken or “dimpled” area found on the AFV CLUB turret ring armor (part # D18)
• Blends the forward section of AFV CLUB part D18 smoothly into the turret sides
• Includes enhanced weld bead details
• Includes more detailed grouser mounts cast onto the turret in an accurate arrangement w/tack-welds
Click thumbnails for slideshow views
    
- 24403 M5A1/M8 Exhausts & Deflector Set w/PE Screens (ALL).
This detail set is designed to be used with the AFV CLUB M5A1 kit# AF35053 but it will work on most M5A1/M8 kits. This set includes:
• Early M5/M8 style exhaust pipes
• M5A1/M8 style exhaust pipes
• Upper exhaust deflector w/hinge details
• Early style lower exhaust deflector (before tow pintle was added)
• Late style lower exhaust deflector (after tow pintle was added)
• TMD PE screens for all three deflectors (as well as engine deck screens for the TAMIYA M5A1/M8 kits)
Click thumbnails for slideshow views
     
- 24409 Early M5 Hull Roof w/o Exhaust Fan Housing (AFV Club)
This is a simple replacement for the AFV Club hull roof. It represents the early roof design of the M5 w/o the exhaust fan housing.
- 24410 M5 Prototype Backdate (AFV Club)
This set includes TMD items # 24409 M5 Early Hull Roof w/o Exhaust Fan and # 24411 M5 Early Backdate. It also includes a new bow plate with the fixed .30 cal MG, flexible bow-mounted MG brush guard and early style brush guard for the left headlight and siren.
This conversion provides:
• everything you need to model an M5 Prototype vehicle hull
• an accurate Early M5 turret with added details and grousers
• enhanced weld bead details
• Includes more detailed grouser mounts cast onto the turret in an accurate arrangement w/tack-welds
Click thumbnails for slideshow views
   
- 25405 M4A2 Corrected Engine Deck Grill Doors (DML)
This is a simple replacement for the engine deck grill doors in DML kits 6062, 6188 and 6313.
This detail set includes:
• Corrected grill pattern on the upper surface of the grill doors
• The three little “nubs” on each door (seen on so many M4A2’s – especially in British service)
• 8 replacement armored fuel filler caps
• 8 inches of 0.020 in lead solder to make door handles and fuel filler cap lock pins
- 35201 T-34 Replacement Exhausts (ALL)
Designed to work in conjunction with TMD T-34 armored exhaust covers and to fit on any T-34 model kit. Have a sidewall less than 0.010 in thickness and cast hollow past the bend in the pipe for added realism.
- 35202 T-34 Hollow Exhaust Pipes (scale thickness) with weld seam detail (ALL)
Designed to work in conjunction with TMD T-34 armored exhaust covers and to fit on any T-34 model kit. Have a sidewall less than 0.008 in thickness and cast hollow past the bend in the pipe with weld seam on inside and outside of the pipe.
 S
- 35207 T-34 8-Bolt Armored Exhausts Housing (ALL)
8-Bolt Armored Exhaust Housings are designed to directly replace any T-34 kit piece. This detail set represents the 8-bolt armored exhaust housings used by the STZ and 112 factories.
- 35208 T-34 45 mm Armored Exhausts Housing (ALL)
5 mm Armored Exhaust Housings are designed to directly replace any T-34 kit piece. This detail set represents the heavier, 40 mm thick armored exhaust housings used by factory 183.
- 36201 KV Replacement Exhausts (ALL)
Designed to work on any KV model kit. Have a sidewall less than 0.010 in thickness and are cast hollow deep into the bend in the pipe for added realism.
- 45201 Valentine Replacement Exhaust (ALL)
- T-34 side fenders with hull weld beads
- T-34 STZ Model 1942 Correction Set
[Complete Upper Hull (for Cyberhobby kit), Turret Main Hatch, Mantlet, exhaust covers, apliquet armor, etc
- T-34 All Steel Wheels ("later" pattern with stiffened lighting holes)
- 13953 SdKfz 9/1 Famo 6-Ton Bilstein Crane Conversion (TAM)
- Re-mastering of original conversion, TMD item # 352020. The crane body remains the same, as does the PE fret and decals. However, totally re-mastered is the entire bed and all the associated parts to reflect additional information we uncovered since we released the first kit.
A partial list of what has changed includes:
•A re-mastered bed. Bed lengthened by 4 mm, opened up the storage boxes in the top of the bed and thinned the master closer to scale thickness.
•New mold techniques and different resin so the bed piece will not deform during casting or warp as much in shipping.
•Re-mastered pieces that make it easier to construct the supporting structures under the bed assembly.
•Re-mastered rear deck storage box using new mold techniques and resin to help reduce warping problems.
•Added the extended spare tire holder, lock mechanism and associated pieces to model the strap that was used to pull the spare tire from storage.
•Re-mastered the cab sides and added the cowl with ALL the rivet detail missing from our old conversion AND the TAMIYA kit.
•Improved masters to aid in constructing the support legs and pads.
•Added the locating rods and handles that go to the support leg pads and were missing from our original conversion.
•Added ears to the travel lock so the lock pin has a place to go, as well as the handle to attach the crane hook to the travel lock arm while in transit mode.
•Added the dust covers for the base of the crane assembly.
•Added the tilt mounting brackets that were missing from our original conversion.
•Re-mastered the wheel chocks to ease construction.
Click thumbnails for slideshow views
     
More info and images to follow when available
|
