PMMS
Trumpeter
Russia KV1 (Model 1942)
Lightweight Cast Turret

Trumpeter Kit No. 00360

1:35th Scale

Review by Terry Ashley

Trumpeter
This is the fifth in Trumpeter’s KV series with this model depicting the KV-1 model 1942 with a lightweight cast turret and armed with the ZIS-5 76.2mm main gun and features the ribbed steel road wheels which are the second of four designs used on the KV series.

The kit consist of consists of 231 parts in light grey plastic with 2 in clear plastic, a length of copper wire for the tow cables, some poly caps for the wheels plus the decal and instruction sheets and has most parts from kit #00358 with just the new Cast Turret and decal sheet. The review below basically the same as for kit #00358 with just updates for the turret.

TrumpeterTrumpeter

The quality of the mouldings is excellent and on a par with the other KV kits with clean crisp details and a minimum of pin parks with those present being very shallow for easy removal.
There is some very minor flash around some parts but a quick pass with model knife or wet and dry deals with this along with the normal small mould seams on the parts.

While there is not a lot of parts there are many small finely moulded parts and excellent surface details such as weld seams and bolt/rivet head details that all add to the overall quality feel.

The kit as mentioned offers a few a optional parts that require the locating holes to be opened up in the hull and engine deck parts before assembly so check the instructions and decide if you will use the optional parts and open up the holes accordingly.

Lower Hull:
The lower hull has a traditional tub with bottom, sides and front panel to which is added the separate outer side and rear panels, this allows different side details to be incorporated without replacing the whole tub, quite nifty. The fit of the side panels to the hull is excellent and once attached form a trough at the top for fitting the upper hull panels.

The side panels have the squared off rear profile and the axle and final drive locating plates are again included with all other details such as axle bump stops, return rollers and final drive mounts added as well as the separate axles. These have hexagonal locating stubs that fit into corresponding hexagonal holes in the hull sides ensuring they are positioned at the correct angle and have separate axle hubs with the correct number of bolts for this version.

The ribbed steel road wheels are made up of the inner and outer wheel which trap a poly cap between them for easy fitting to the axles and look very good when compared to photos of the real wheels but remember there are three types of steel wheel used on the KV series so make sure you are looking at the right ones.

The drive sprockets have bolt head and other details on both sides of the inner and outer disc as well as having the central hub disc as two separate parts with the correct number of retaining bolts for this version.

The idler wheel mount has a three part tensioning arm for good definition while the idler wheel has the two wheel discs with excellent rib details and the three part return rollers with separate hub cap are also the correct type for this model KV with well defined details and finally there is a the drive sprocket mud clearing device fitted to the rear hull sides which you have to fit at the same time as the drive sprockets as it is very difficult to fit the sprockets once the cleaning devise is in place.

At either end are separate towing attachments and shackles, these have sizable mould seams but should be easy enough to clean up.

Tracks:
You are again given a choice of full length vinyl tracks or pre-formed sections of plastic link and length track to use depending on your choice with the vinyl track having excellent details on both sides and looks very good for this type of track and is also very flexible to help with track sag. The plastic track incorporates pre-formed track sag along the top run and another long section for the ground run and individual links for around the drive and idler wheels. The details on the plastic track are again excellent but there are some shallow pin ejector marks on the inside to be removed which shouldn’t be a problem.

Just a quick note here if you prefer fully workable tracks, check the KV Resource Page for the various track sets now available for the Trumpeter KV kits.

Upper Hull:
The upper hull panels are in two sections with the forward section including the turret race forward to the glacis and the rear engine deck; this allows easy replacement of the engine deck for other versions without replacing the whole upper deck. The fit of these panels to the lower tub is excellent with any minor edge gaps small enough to be filled with glue as you attach the panels. Added to the top panel is a separate turret ring which allows more details to be included than if the ring was moulded with the hull top, but unfortunately there is a series of pin ejector marks around the ring that will have to be filled while at the front is a separate smooth finish nose cap.

Features added for this version are the large V shaped bullet splash shield in front of the turret ring and on the outer edges of the engine deck with nice weld seam details. Note you have to open up the locating holes for the forward shield before attaching the upper hull panel.

There are subtle weld seams on the forward hull section and excellent bolt head and panels details on the engine deck as well as inner vanes under the two side intake grills. These side intake grills are interesting in that they are moulded solid with nice mesh details as well as offering a choice of grills, one with rounded end profiles and other with one flat end profile (see images) and you should check references to see which applies to particular vehicles. Being moulded solid these grills obviously hide the inner vanes but there will no doubt be after market etched screens produced and already having the inner vanes is nice forward thinking by Trumpeter.

The front crew hatch has a separate hatch lip and the hatch has interior latch details as well as a small hinge to allow the hatch to be positioned open if required. On the driver’s plate is the added armour panel for this version as well as a separate visor cover, horn with separate wiring ducting, the head light with separate clear lens and three part machine gun mounting as well as separate periscope cover on the hull top all with well defined details.

The engine deck is different from previous models with the square welded rear section and has separate round inspection hatches again with interior latch details and hinge as well as a new separate engine access hatch and optional centre hatch (you have to open up the locating hole to add this if required). Also added to the engine deck are eight very small lifting eyes that will need careful removal from the sprue and in gluing, with tweezers being the order of the day.

The original round domed engine access hatch is also included to use as an alternative if desired, but check references to see which is most applicable.

At the rear are two additional panels that make up the engine louvers under the curved rear hull panel and the exhaust outlets are also separate parts with the fit of the centre panel and all parts are excellent with out any trimming needed.

The copper wire provided is used for the two tow cables and are attached to the later style end shackles which are hollowed out using slide moulds allowing the cable to fitt centrally for a realistic finish.

Fenders:
These are full length either side with very nice surface details of rivet heads and securing strips as well as a nice outer lip and also include the longitudinal centre stiffening bar on the undersides. You have to open up a few locating holes for the fender storage boxes and other fittings applicable to this version before assembly, so check the instructions carefully and there are some shallow pin marks on the underside that are easy to remove.

One thing of note here is the forward side panel between the fender and glacis which is included with the main fenders and moulded using slide moulds resulting in well defined details on this panel.

The fender supports are all separate parts for good definition with the fit of the fenders to the hull being very good and again any minor gaps will be filled with the glue residue as they are attached. There are alternate fender supports provided with the solid type and the hollow type for variety depending on the version being modelled.

It should also be noted that the fenders in the two later kits with steel road wheels (00358, 00359 and 00360) are 1.5mm narrower than the fenders in the earlier kits with resilient road wheels (00312 and 00356).

The Turret:
The new lightweight cast turret is in two halves with a separate roof and lower turret ring section with a fine weld seam depicted on the lower sides of the turret. The top panel has the large interleaved joins with the small step from the turret sides to the roof and includes the top ventilator and hatch lip with all other parts separate.

The fit of the turret parts is very good with large locating pins for the turret sides that hold the parts firmly in place with the top panel fitting snugly in place without any trimming required.

On the top is the early style forward sighting periscopes with separate base plates and the later style side and rear facing periscope covers as well as two very fine grab handles.
The top hatch again has internal latch details and separate hinge allowing this to be shown open but there are no interior details to show.

The original ZIS-5 mantlet has very well defined bolt heads and weld seams that look quite impressive with the barrel moulded in one piece with the muzzle hollowed out using slide moulds although there is a minor moulding seam to be removed.

The mantlets fits snugly between the outer rounded gun mounts while at the rear is a three part machine gun mounting with equally well defined details.

Instructions:
These are the usual exploded view drawings and are very clear and easy to follow although you should read the opening steps carefully to determine what if any locating holes need to be opened up for the different fittings

Decals:
The decals are nicely printed with thin carrier film cropped close to the printed image and give you markings for two vehicles but only one is shown in the instructions and on the box sides. A full colour sheet is included showing the vehicle and can be used a painting guide as well as showing the decal placement.

Trumpeter

Conclusion:
Another excellent KV kit with well defined details that adds yet another variant to the growing stable of KV types in this superb series and sure to be another hit.

Highly recommended.

The Sprues:

Click on thumbnails for larger view
TrumpeterTrumpeterTrumpeterTrumpeter
TrumpeterTrumpeterTrumpeterTrumpeter
Detail Images
TrumpeterTrumpeterTrumpeterTrumpeter
Close new window to return to review

See the KV Resource Page for full listings of updates/accessory and other KV reviews on site.

References:

KV-1 Soviet Heavy Tank of WWII - Early Variants
Tankograd Soviet Special
No. 2002
book
KV-1 & 2 Heavy Tanks
1939-1945

Osprey New Vanguard 17
ISBN 1-85532-496-2
book
Ground Power Magazine
#75 - 8/2000
Published by GALILEO
Publishing Co.,Ltd.
book
Russian Tanks and Armored Vehicles 1917-1945
Schiffer Publishing
ISBN: 0-7643-0913-7
book
Stalin's Heavy Tanks
1941-1945

Concord Armor at War
Series #7012
book
Stalin's Giants KV-1 & KV-II
Schiffer Publishing
ISBN: 0-8874-0404-9
book
KW
Wydawnictwo Militaria #34
book
KW Vol.I
Wydawnictwo Militaria #163
book
KW Vol.II
Wydawnictwo Militaria #168
book

Kit courtesy of my Credit Card and the excellent service from Rainbow Ten.



Page created March 23, 2006

Click Browsers BACK button to return to list
Home / Reviews / Vehicle Reviews / Trumpeter